Paver sealing for Arlington homes
Paver Sealing in Arlington, FL
Pavers fading in Arlington? Get local help from Neptune Beach Paver Sealing. Call (904) 906-9979
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligations.
Paver sealing help in Arlington
Once the Mathews Bridge opened in 1953, young families moved across the St. Johns into Arlington, and many of the homes they bought in the 1950s and 1960s still stand. The pavers added since have had decades of sun and storms. Maybe your front walk has faded to chalky gray with sand gone from the seams. Clean it, re-sand it and seal it, and the color comes back even from the street to the door. To start, request a quote for a free estimate with no obligation.
The company behind this website does no sealing of its own. It connects Arlington homeowners to an independent contractor, and the contractor inspects the pavers, quotes the work and carries it out. If you have a question first, call (904) 906-9979 and describe what your driveway or patio looks like.
5 common paver problems in Arlington
Sand that will not stay put
Parts of Arlington were built on old dune ground. Regency Square went up in 1967 on former sand dunes, and the Arboretum land off Millcoe Road was strip-mined down to barren white sand. With about 52 inches of rain a year, joint sand on pavers across this part of town gets a steady beating. A local paver company says downpours flush sand from unsealed joints, which means the weeds in your walkway often started as a missing inch of sand.
Creek and river water after a storm
Pottsburg Creek widens as it enters southern Arlington and drains to the Arlington River, and storm water from all over the Southside feeds it. Its boat ramp along Beach Boulevard flooded during Nicole in 2022, and Hurricane Irma brought record St. Johns River flooding in 2017. Pavers that took on storm water can hold a film of dirt. Sealer would lock that film in, so an Arlington driveway near the water needs a full wash first.
Roots under a mature yard
One Jacksonville writer calls Arlington's mature landscape an overlooked asset, and the live oaks on the Arboretum's Live Oak Trail are more than a century old. Trees that big send out roots, and a local paver company says a section lifted by roots has to be reset before sealing. Sealer over a bump only preserves the bump. Walk your Arlington driveway after a rain and look for the spot where water pools.
White haze from sealing too soon
Jacksonville summers are hot and humid, and an Arlington patio under old trees can hold moisture long after the sun returns. A Jacksonville paver company says most sealer that turns white traces back to damp pavers or too thick a coat. If your last job went cloudy within a season, that may be why. Ask how the contractor checks dryness before opening a pail.
Sealer from a long list of owners
River Forest is mostly 1950s and 1960s ranch homes, and Arlingwood is mostly brick ranch with a median build year of 1961. Pavers came later on many of these lots, and they may have been sealed more than once by owners you never met. Water-based sealer cannot go over solvent-based sealer, so an Arlington contractor has to learn what is on there. A spot of peeling or patchiness is a good place to start the conversation.
River Forest, Arlingwood, Clifton and the river blocks
River Forest sits in ZIP 32211, about three miles east of downtown, and most of its homes are ranches from the 1950s and 1960s. Arlingwood nearby is mostly brick ranch, some two-story. Neither one has a mandatory homeowners association on record, so there may be no board to clear a finish with, but check your deed to be sure. Pavers meeting old brick call for careful rinsing, so mention the walls when you request a quote.
Along the river, Clifton began when the Ocean Grove Association bought the land in 1873, and it is a residential community today. Monterey sits on the same stretch of the St. Johns, running between the Arlington River and Mill Cove. From downtown to Mayport the river turns estuarine, and the water gets saltier past downtown. If your Arlington lot backs up to that water, call (904) 906-9979 and say how close you are.
Arlington is also known for mid-century modern houses with sharp edges and sloping roofs, some designed by Robert C. Broward, Taylor Hardwick and William Morgan. A paver patio beside one of those low, angular homes can put rinse water right against glass and painted wood. A contractor who has seen that kind of house will plan the wash around it. You can request a quote and describe your home's style in a line or two.
Why Arlington chooses Neptune Beach Paver Sealing
You could call around and compare a long list of companies in Duval County yourself. This site exists so you do not have to. To try it, request a quote.
Free estimate
Tell us what you need in Arlington and a contractor who works in the area will look at the job and price it.
Local price range
Northeast Florida companies commonly publish $1.50 to $2.50 per square foot for clean, sand and seal, so you know the range going in.
Your choice of finish
Pick a natural matte look or a deeper wet look. The contractor can explain how each one will wear on your surface.
You decide
Get the price in writing and take your time. Nothing moves forward at your Arlington home until you say so.
Get Your Free Estimate in Arlington
Tell us about your pavers in Arlington.
Free, no obligations
Paver sealing pricing in Arlington
Published rates from Northeast Florida companies run $1.50 to $2.50 a square foot to clean, sand and seal, and Arlington jobs follow that same range. On older Arlington lots, the things that move a job up that range are lost joint sand, patchy sealer and root damage that has to be repaired first. A short ranch-house driveway measures small, so the total can stay modest even at the same rate. To get your own figure, request a quote, and it is free.
Older lots can make access harder. A narrow side yard beside a 1950s ranch means carrying gear by hand, and a patio tucked behind a mature tree may need extra time for the wash and for drying. Storm film on a lot near Pottsburg Creek adds to the wash too. Call (904) 906-9979 and ask which of these apply to your address, with no obligation.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $450 to $750 |
| 600 sq ft | Two car driveway | $900 to $1,500 |
| 1,000 sq ft | Large driveway or pool deck | $1,500 to $2,500 |
| 1,500 sq ft | Driveway plus pool deck | $2,250 to $3,750 |
Math based on the $1.50 to $2.50 per square foot that Northeast Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.
How a paver sealing job works in Arlington
Walk the old slabs and see what lifted
The contractor begins by checking where roots or settling have moved your Arlington pavers, and how the surface sheds water. Those spots need repair before sealing, since a coat preserves any lift or dip. If the surface was sealed before, the product decides what can go on next. Point out any sections that lifted after a storm or a big rain.
Wash the walk and the storm film
Next comes the wash, with attention to any film left by storm water and any green growth in the shade. Rinse water should stay away from old brick mortar and wood trim on 1950s Arlington homes. Washing pulls sand out of the joints, which is part of the plan. Ask how the contractor protects your plantings along the walk.
Reset the sand in every joint
With the old sand gone, the joints get refilled before sealing. On the sandy ground around Arlington, an open joint lets soil settle in and gives weeds their start. The contractor sweeps the sand in and checks for low spots at the edges. Long neglected joints along a driveway can take a while, so expect this part to run longer on older lots.
Let the humidity lift
Sealer needs a dry surface, and summer in Arlington is hot, humid and full of quick storms. A patio under old oaks may stay damp hours after a driveway in full sun is ready. Most white or cloudy sealer goes back to damp pavers or too heavy a coat, according to a Jacksonville paver company. A patient contractor will wait rather than risk a haze.
Lay down the coat and leave it be
The sealer goes on, usually sprayed and then back-rolled so it reaches the joints. A wet look shows scuffs sooner than matte, which matters on a busy family driveway in Arlington. Companies commonly quote two to five years between coats on Arlington driveways. One Jacksonville company says people can usually walk on a fresh coat within hours and cars need about a day.
Complete paver services in Arlington
A complete sealing job has three stages. The surface is cleaned to remove algae, dirt and old residue. Fresh sand goes back into the joints, which helps keep pavers locked in place and gives weeds less room to grow. Once everything is dry, a water-based or solvent-based sealer goes on in a matte or wet look finish. To ask about any of these stages, call (904) 906-9979.
Driveways, walkways, patios and pool decks can all be sealed, and each takes different wear. A driveway deals with tires and oil. A pool deck deals with water and foot traffic. Shaded side yards tend to grow algae first. Let the contractor know how each area is used when you request a quote.
Sealer choice matters more than most homeowners expect. Water-based products are low odor and clean up easily, and can later be followed by either type. Solvent-based products typically give a higher gloss but generally have to be followed by solvent-based products. For help deciding, call (904) 906-9979.
Timing matters too. Sealer needs a dry surface, so a contractor will plan around rain and allow drying time after washing. If it has been a few years since your last coat, this is a good time to request a quote.
Questions to ask before you hire
- Which sealer will you use, and does it work with what is already on my pavers?
- Does your price include cleaning, joint sand and any repairs?
- How do you handle rain in the forecast?
- Can you show proof of insurance and any license the work requires?
- What happens if the finish turns cloudy?
- How long should I stay off the pavers once the sealer is down?
- When do you expect it will need another coat?
Why local matters in Arlington
A contractor who knows Arlington knows the housing is old enough that pavers may have been added in pieces over the years. That changes how the old sealer behaves and where the joints have gone soft. A contractor used to brand-new builds may not plan for that. To reach a contractor who works in Arlington, call (904) 906-9979.
Water is the other local problem. Pottsburg Creek and the Arlington River carry storm runoff through the south end of the neighborhood, and the St. Johns gets saltier as it runs past downtown. A contractor who knows Arlington will ask how close you are to any of that before setting a date. You can request a quote and tell the contractor when your lot last took on water, with no obligation to hire anyone.
Tree cover matters too. Older trees throw shade that keeps patios damp and roots that shift pavers, and a sealing day has to account for both. A contractor from this side of the river plans the drying time around shade instead of guessing. If your Arlington yard has big trees close to the pavers, request a quote and mention how much of the surface they cover.
A suburb built for the automobile
Arlington has been called Jacksonville's first major post-war suburb, built around the car. H. Terry Parker started buying land around 1943 and later donated thirty acres for what is now Terry Parker High School. Jacksonville University opened its first building here in 1950, three years before the Mathews Bridge. If your driveway sits in one of those early blocks, request a quote for a free estimate.
Plenty of older places still stand. Norman Studios sits at 6337 Arlington Road, Tree Hill Nature Preserve covers 50 acres on Lone Star Road, and the Crossroads marks University Boulevard North and Arlington Road. The Jacksonville Arboretum grew up on land that was strip-mined until 1961. To talk with a contractor who works around these Arlington landmarks, call (904) 906-9979.
Frequently Asked Questions
What is the average cost to seal pavers in Arlington?
Expect $1.50 to $2.50 a square foot to clean, sand and seal in Arlington, the range Northeast Florida companies commonly publish. Patchy old sealer and root repairs push an Arlington job higher. Ask for a written square footage so you can compare it to that range.
How much does it cost to seal outdoor pavers like an Arlington patio?
It comes down to the measured area times a rate in that same $1.50 to $2.50 range. A small Arlington patio will total less than a full driveway, though small jobs may carry a minimum. Tree shade and tight side yards can add time. Ask if the joint sand is part of the quote.
What's the average cost to seal pavers on a small walkway?
The same per-square-foot range applies, so a walkway usually totals little compared with a driveway. Short runs may be subject to a minimum job size, so ask up front. Bundling a walkway with a driveway can make better use of the trip. A walkway next to a brick ranch may also need more careful rinsing.
Is it good to seal pavers in Arlington?
Yes, for most homeowners it is worth doing here. A Jacksonville paver company says summer storms flush sand from joints that were never sealed, and Arlington gets around 52 inches of rain a year. Sealing does need upkeep, because companies commonly quote two to five years between coats.
Can pavers next to a 1950s brick ranch be sealed safely?
Yes, as long as the wash and the sealer are kept off the brick. Old mortar and painted trim on an Arlington ranch call for more careful rinsing than new stucco would. Mention the age of the house when you get your quote.
Why did the sealer on my pavers turn white?
The usual cause is sealing damp pavers or laying the coat on too thick, according to a Jacksonville paver company. Humid Arlington summers and shaded patios make that easier to do by accident. A local contractor can tell you what it takes to correct it once they see the surface.
Should tree roots be fixed before I seal my Arlington driveway?
Yes, lifted sections should be reset first. A Jacksonville company notes that sealing over a lift only preserves it. Point out any spots where a root has moved the surface so they can be priced before work starts.
How can I tell if the sealer on my Arlington pavers is worn out?
Sprinkle water on the surface and watch what it does. A Jacksonville paver company says water that beads means the coat is still working, and water that soaks in and darkens the paver means it is spent. Try it on a sunny part of the driveway and again on a shaded Arlington patio, since the two can wear at different speeds.